2 stroke engine PV diagram

C) The Air-Standard Diesel Cycle (Compression-Ignition) Engine

The Air Standard Diesel cycle is the ideal cycle for Compression-Ignition (CI) reciprocating engines, first proposed by Rudolph Diesel over 100 years ago. The following link by the describes the operation including a short history of Rudolf Diesel. The four-stroke diesel engine is usually used in motor vehicle systems, whereas larger marine systems usually use the . Once again we have an excellent animation produced by presenting the operation of the .

The actual CI cycle is extremely complex, thus in initial analysis we use an ideal "air-standard" assumption, in which the working fluid is a fixed mass of air undergoing the complete cycle which is treated throughout as an ideal gas. All processes are ideal, combustion is replaced by heat addition to the air, and exhaust is replaced by a heat rejection process which restores the air to the initial state.

The ideal air-standard diesel engine undergoes 4 distinct processes, each one of which can be separately analysed, as shown in the P-V diagrams below. Two of the four processes of the cycle are adiabatic processes (adiabatic = no transfer of heat), thus before we can continue we need to develop equations for an ideal gas adiabatic process as follows:

The analysis results in the following three general forms representing an adiabatic process:

where k is the ratio of heat capacities and has a nominal value of 1.4 at 300K for air.

Process 1-2 is the adiabatic compression process. Thus the temperature of the air increases during the compression process, and with a large compression ratio (usually > 16:1) it will reach the ignition temperature of the injected fuel. Thus given the conditions at state 1 and the compression ratio of the engine, in order to determine the pressure and temperature at state 2 (at the end of the adiabatic compression process) we have:

Work W1-2 required to compress the gas is shown as the area under the P-V curve, and is evaluated as follows.

An alternative approach using the energy equation takes advantage of the adiabatic process (Q1-2 = 0) results in a much simpler process:

(thanks to student Nichole Blackmore for making me aware of this alternative approach)

During process 2-3 the fuel is injected and combusted and this is represented by a constant pressure expansion process. At state 3 ("fuel cutoff") the expansion process continues adiabatically with the temperature decreasing until the expansion is complete.

Process 3-4 is thus the adiabatic expansion process. The total expansion work is Wexp = (W2-3 + W3-4) and is shown as the area under the P-V diagram and is analysed as follows:

Finally, process 4-1 represents the constant volume heat rejection process. In an actual Diesel engine the gas is simply exhausted from the cylinder and a fresh charge of air is introduced.

The net work Wnet done over the cycle is given by: Wnet = (Wexp + W1-2), where as before the compression work W1-2 is negative (work done on the system).

In the Air-Standard Diesel cycle engine the heat input Qin occurs by combusting the fuel which is injected in a controlled manner, ideally resulting in a constant pressure expansion process 2-3 as shown below. At maximum volume (bottom dead center) the burnt gasses are simply exhausted and replaced by a fresh charge of air. This is represented by the equivalent constant volume heat rejection process Qout = -Q4-1. Both processes are analyzed as follows:

At this stage we can conveniently determine the engine efficiency in terms of the heat flow as follows:

__________________________________________________________________________

The following problems summarize this section:

Problem 3.4 - A frictionless piston-cylinder device contains 0.2 kg of air at 100 kPa and 27°C. The air is now compressed slowly according to the relation P Vk = constant, where k = 1.4, until it reaches a final temperature of 77°C.

• a) Sketch the P-V diagram of the process with respect to the relevant constant temperature lines, and indicate the work done on this diagram.
• b) Using the basic definition of boundary work done determine the boundary work done during the process [-7.18 kJ].
• c) Using the energy equation determine the heat transferred during the process [0 kJ], and verify that the process is in fact adiabatic.

Derive all equations used starting with the basic energy equation for a non-flow system, the equation for internal energy change for an ideal gas (Δu), the basic equation for boundary work done, and the ideal gas equation of state [P.V = m.R.T]. Use values of specific heat capacity defined at 300K for the entire process.

Problem 3.5 - Consider the expansion stroke only of a typical Air Standard Diesel cycle engine which has a compression ratio of 20 and a cutoff ratio of 2. At the beginning of the process (fuel injection) the initial temperature is 627°C, and the air expands at a constant pressure of 6.2 MPa until cutoff (volume ratio 2:1). Subsequently the air expands adiabatically (no heat transfer) until it reaches the maximum volume.

• a) Sketch this process on a P-v diagram showing clearly all three states. Indicate on the diagram the total work done during the entire expansion process.
• b) Determine the temperatures reached at the end of the constant pressure (fuel injection) process [1800K], as well as at the end of the expansion process [830K], and draw the three relevant constant temperature lines on the P-v diagram.
• c) Determine the total work done during the expansion stroke [1087 kJ/kg].
• d) Determine the total heat supplied to the air during the expansion stroke [1028 kJ/kg].

Derive all equations used starting from the ideal gas equation of state and adiabatic process relations, the basic energy equation for a closed system, the internal energy and enthalpy change relations for an ideal gas, and the basic definition of boundary work done by a system (if required). Use the specific heat values defined at 1000K for the entire expansion process, obtained from the table of .

Solved Problem 3.6 - An ideal air-standard Diesel cycle engine has a compression ratio of 18 and a cutoff ratio of 2. At the beginning of the compression process, the working fluid is at 100 kPa, 27°C (300 K). Determine the temperature and pressure of the air at the end of each process, the net work output per cycle [kJ/kg], and the thermal efficiency.